[gradsusr] problem with 3D figure

[cellyn lee]

Hi,
 
I  solved my problem already with your guide, thank you very much!! I done it without the VARS statement.
thanks again.
 
Regrads,
Cellyn

--- On Thu, 3/6/10, Heiner Körnich <heiner at misu.su.se> wrote:


From: Heiner Körnich <heiner at misu.su.se>
Subject: Re: [gradsusr] problem with 3D figure
To: "GrADS Users Forum" <gradsusr at gradsusr.org>
Date: Thursday, 3 June, 2010, 2:59 PM


Hi,

only open the .ctl-file with xdfopen.
The ctl-file should contain something like:
DSET data.nc
ZDEF dep 12 linear 1 1

This would mean that your height variable is called "dep" in the .nc-file. Check it with 'ncdump -h data.nc'. For the level definition the example uses only linear distributed levels, you might want to put their actual levels.

Since you have mentioned that your file contains both 2d and 3d data, you might need to add this as a "VARS"-statement in the ctl-file. But try with out.

So far,
Heiner


On Wed, Jun 2, 2010 at 7:04 PM, cellyn lee <cellyn_lee53 at yahoo.com> wrote:






Hi,
 
thanks for your information, it helps me a alot. but i stil have a question, is it i should sdfopen the original .nc file, then only xdfopen the .ctl file??
 
Regards,
cellyn


--- On Tue, 1/6/10, Heiner Körnich <heiner at misu.su.se> wrote:


From: Heiner Körnich <heiner at misu.su.se>
Subject: Re: [gradsusr] problem with 3D figure
To: "GrADS Users Forum" <gradsusr at gradsusr.org>
Date: Tuesday, 1 June, 2010, 4:27 AM





Hi, 


this happens sometimes, when the netcdf file does not follow a certain standard. You have to create a small control-file and open the file with the commmand xdfopen.
It is all well described in the GraDS documentation index under "xdfopen":
http://grads.iges.org/grads/gadoc/gadocindex.html


Regards,
Heiner


On Sun, May 30, 2010 at 5:24 PM, cellyn lee <cellyn_lee53 at yahoo.com> wrote:






Hi…I met some problem in displaying 3D variables in GrADS. My netcdf file included 15 variables, some variables are 2D while some are 3D, when I type ‘q file’, the Z size is 1, let’s say I have dep=15 in my 3D variables, so how I display the 3D variables where dep=12? 
Thanks for any information.





_______________________________________________
gradsusr mailing list
gradsusr at gradsusr.org
http://gradsusr.org/mailman/listinfo/gradsusr




-- 
Heiner Körnich    
Dept. of Meteorology            Tel:  +46 8 164333
Stockholms University, SE-106 91 Stockholm, Sweden
Email: heiner at misu.su.se   www.misu.su.se/~heiner/

-----Inline Attachment Follows-----





_______________________________________________
gradsusr mailing list
gradsusr at gradsusr.org
http://gradsusr.org/mailman/listinfo/gradsusr


_______________________________________________
gradsusr mailing list
gradsusr at gradsusr.org
http://gradsusr.org/mailman/listinfo/gradsusr




-- 
Heiner Körnich    
Dept. of Meteorology            Tel:  +46 8 164333
Stockholms University, SE-106 91 Stockholm, Sweden
Email: heiner at misu.su.se   www.misu.su.se/~heiner/

-----Inline Attachment Follows-----


_______________________________________________
gradsusr mailing list
gradsusr at gradsusr.org
http://gradsusr.org/mailman/listinfo/gradsusr


-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://gradsusr.org/pipermail/gradsusr/attachments/20100603/534e9117/attachment-0003.html